MUSMYS Clone Study Acceleration E-406 Class AB 320W/4ohm 180W/8ohm Fully Balanced Amplify SNR 120dB HIFI Amplifier

Features:

1: The whole machine adopts 24 German IXYS Essex MOS field-effect high-power transistors, each with a current of 30A and a power of 450 watts, far exceeding that of Toshiba Ansemy high-power transistors.

2: Using MUSMYS to customize 320000 microfabric capacitors for super large ponds, far exceeding similar products.

3: Using 850W full strip steel sheet, large diagonal iron core, pure copper winding, far beyond the comparison of ordinary transformers.

4: Using the latest American technology, third-generation AC power purification technology, to isolate dirt from the source in the mains.

5: We use the latest generation power supply for soft start to ensure stable operation during startup. Our power supply has a very large capacity, which is not comparable to ordinary power amplifiers. Charging a 320000 microf capacitor can instantly reach 160A

6: The use of a completely symmetrical and independent power amplifier board with left and right channels greatly improves the separation of sound.

7: Using NEC signal relay purely mechanical to switch sound source signals, rejecting sound coloration, using 2 Omrons

16A ultra high current relay serves as speaker protection, with separate left and right channels to protect you

Expensive speakers.

8: Using 2 sets of speaker terminals for output, the speaker can be split into two lines, with Group A connected to mid high frequencies and Group B connected to low frequencies, fully tapping into the potential of the speaker.

9: Using Taiwan pure copper speaker wiring terminals can greatly improve the damping coefficient of the amplifier and enhance its strength.

10: Adopting dual header dynamic display, retro and charm coexist, and adopting logical calculation method is more natural.

11: The all aluminum chassis showcases a high-end atmosphere, with an iron frame inside to make the overall chassis more sturdy and eliminate resonance

E-406 Technical Parameters：

Rated continuous output power (20HZ-20000HZ)

Pure Class A :60W*24 ohm output

Pure Class A: 30W*28 ohm output

Class AB : 320W*2 4 Ohm Output

Class AB:180W*2 8 Ohm Output

Frequency response:

Continuous rated output 20-20000HZ+0-0.2db

1W output 0.5-160000HZ+0-3 db

S/N signal-to-noise ratio, full frequency band 120dB

Input impedance:40K (balanced input), 20K (RCA input)

Input sensitivity:

0.87V rated continuous average output

0.11V output 1W power

Distortion:0.005%

Magnification factor:28dB

Size: L430*W430*H160 MM

Weight: about 22KG

The MUSMYS E-406 pure power amplifier was designed based on the amplifier part of the Acceleration E-406. The Acceleration E-406 was not only a famous device of the year, but also left a very glorious page in the history of Golden Voice audio. In terms of production, materials, and performance, it was impeccable and became a popular tool of the generation.

The internal layout is clean and orderly, and the materials used are clear at a glance

The MUSMYS E-406 pure power amplifier is not only a high-power Class A and Class B power amplifier, but also a pure Class A power amplifier in low to medium volume situations. It can output 60 watts of Class A power at 4 ohms and 30 watts of Class A power at 8 ohms, which is similar to the once popular Maranz PM90. However, the Maranz Class A output is 20 watts, so don't underestimate our 30 watt Class A output, Think about the 845 single ended electronic tube with a Class A output power of only 15 watts, and the sound is still earth shattering. Moreover, we still have Class A and Class B reserve power. When the peak of the big dynamic arrives, it automatically switches to a 320 watt 4-ohm output, making it possible for a pair of 12 inch speakers to be small KS

The MUSMYS E-406 pure power amplifier also takes special care of old enthusiasts, equipped with 2 sets of speaker terminals. You can connect 2 pairs of speakers at the same time or connect dual line splitters. Group A can connect to the mid high pitch of the speaker, and Group B can connect to the low pitch of the speaker. Different wires can be used to achieve the desired sound, squeezing out the potential of the speaker after drinking.